REMOTE CONTROLLER
MANUAL
DVC/DVH Series
Inverter Single Zone
Ductless Mini-Split
Heat Controller
DVC/DVH Remote Controller
Remote Control Instructions
The remote controller can be used to control and operate the unit
The remote’s signal can transmit up to 26 ft. (8 m) away.
Any obstructions between the signal of the remote control and the
indoor unit can interfere, limiting the capacity of the signal.
When a button is pressed on the remote control, the indoor unit
will emit a “beep”, which indicates that the command has been
received and transmitted to the indoor unit.
26 ft.(8 m)
!
CAuTION
• The air conditioner will not operate if curtains, doors or other materials block the signal from the
remote control to the unit.
• Avoid spilling any liquid into the remote.
• Do not expose to direct sunlight or heat.
• If the infrared signal receiver on the indoor unit is exposed to direct sunlight, the air conditioner
may not function properly. Use curtains to prevent the sunlight from interferring with the
receiver’s signal.
• If other electrical appliances signals react to the signal sent by the remote controller relocate
these appliances.
• When replacing batteries, do not use old batteries
•If you do not use the remote for a prolonged period of time, remove the batteries. Otherwise
they may leak and damage the remote
Battery Specification
To use the remote control, it is necessary to install two (R03/LR03x2) alkaline AAA batteries.
Battery Replacement
1. Batteries should be replaced when there is not a “beep” heard from the indoor unit or the signal
indicator light does not illuminate when buttons are pressed on the remote or when the indoor unit
does not respond to the remote controls commands.
2. To replace the batteries:
A. Remove the cover by pressing and sliding off.
B. Remove the old batteries and insert the new batteries, placing the (+) and (-) ends correctly.
C. Reattach the cover by sliding it back into position.
NOTE: When the batteries are removed, the remote controller erases all user settings. After inserting
new batteries, the remote controller must be reprogrammed for any user specific settings.
3
DVC/DVH Remote Controller
Heat Controller
Remote Controller Specifications
Model
RG52B/BGEu
3.0V
Rated Voltage
Signal Transmission Distance
Operating Environment
26ft (8m) with full batteries
23°F~ 140°F (-5~60°F)
Performance Features
1. Operating Modes: AUTO, COOL, DRY, HEAT
(heat pump models only) and FAN.
2. 24 hour timer
3. Temperature Range Selection: 62°F~ 86°F.
4. LCD (Liquid Crystal Display)
NOTE: Remote controller can be set to display degrees in °C
or °F. To alternate between unit of measure, press and hold
the temp
and
button at the same time. Release
buttons when the unit of measure changes. Repeat the
process to revert back to the previous unit of measure.
4
Heat Controller
DVC/DVH Remote Controller
Functions
1
2
ON/OFF
Press this button to power on, which starts the unit’s
operation. Push the button again to power off, which
stops the unit’s operation.
MODE
Each time this button is pressed, a mode is selected in
a sequence of AUTO, COOL, DRY, HEAT*, and FAN
then repeat.
*
*Heat mode is applicable to heat pump models only.
3
4
FAN
Press to select the fan speed in four intervals:
SLEEP
Press this button to activate the SLEEP mode. Press it
again to deactivate. This feature can only be selected
when the unit is in COOL, HEAT*, or Dry mode. Use this
feature for the most comfortable temperature control
while you sleep and your body temperature rises.
*Heat mode is applicable to heat pump models only.
5
TuRBO
Activates or deactivates the Turbo function. Press this
button for Turbo function. Turbo function enables the
unit to reach the set temperature in the shortest time. In
the cooling mode, the unit will blow cold air at a super
high fan speed. In heating mode*, the unit will blow hot
air a super high fan speed.
*Heat mode is applicable to heat pump models only.
6
SELF CLEAN
This function helps to keep the inside of the unit dry and
prevents mold from forming. It is particularly useful at
the end of the season when the unit will not be in use
for a long period of time. Press the self clean button to
initiate the self cleaning function.
5
DVC/DVH Remote Controller
Heat Controller
Functions
7
TEMP uP (
)
Push this button to increase the indoor temperature set
point in 1°F increments up to 86°F.
TEMP DOWN (
)
Push this button to decrease the indoor temperature set
point in 1°F increments down to 62°F.
8
SHORTCuT
• Used to restore the current settings or resume the
previous setting.
• The first time the unit is powered on and the
SHORTCUT button is pressed, the unit will operate in
AUTO mode, 80°F set temp, and auto fan speed.
• Pushing this button will automatically revert back to
the previous settings including operating mode, set
temperature, fan speed level and sleep feature (if
activated) and transmit the signal to the unit.
• When this button is pressed for more than 2
seconds, the system will automatically restore the
current operation settings including operating mode,
set temperatures, fan speed and sleep feature (if
activated).
9
TIMER ON
Press the button to initiate the auto-on timer sequence.
Each press will increase the auto-on timer setting in
30 minutes increments. When the set time displays 10,
each addition time the button is pressed, it will increase
the auto-on timer setting in 60 minute increments. To
cancel the auto-on timer program, simply adjust the
auto-on time to 0.0.
6
Heat Controller
DVC/DVH Remote Controller
Functions
10
TIMER OFF
Press the button to initiate the auto-off timer sequence.
Each press will increase the auto-timer setting in
30 minutes increments. When the set time displays
10, each additional time the button is pressed it will
increase the auto-timer setting in 60 minute increments.
To cancel the auto-timer program, simply adjust the
auto-off timer to 0.0.
11
DIRECT
Press this button to direct the airflow by selecting the
position of the louver on the unit. Each time the button
is pressed the louver will open/close by 6° increments.
NOTE: If the louver moves in a position that could affect
the cooling or heating (heat pump models only) of the
air conditioner, the unit will alter the direction of the
louver angle automatically.
12
SWING
Press this button to start/stop the auto swing feature,
which the louver oscillates up and down.
NOTE: If the louver oscillates or moves in a position
that could affect heating (heat pump models only) or
cooling of the air conditioner, the unit will automatically
adjust the louver position.
13
FOLLOW ME
Push this button to initiate the Follow Me mode. In
follow me mode, the temperature sensor built into the
remote control senses the room temperature in place of
the sensor inside the indoor unit. This allows the remote
control to control the temperature of the room where
it is present. This feature helps prevent temperature
stratification. When in follow me mode, the remote
control display will show the actual room temperature it
senses.
14
LED
Disables/Activates the indoor \Display. When pushing
the button, the indoor screen is cleared, press it again
to turn on the light of the display.
7
DVC/DVH Remote Controller
Heat Controller
Remote Control Display
MODE
Displays the current operation mode. Including auto (
),
cool (
auto (
), dry (
).
), heat* (
), fan (
) and back to
*Applicable to heat pump models only
TRANSMISSION INDICATOR
This transmission indicator lights when remote controller
transmits signals to the indoor unit.
ON/OFF
Shows when unit is on.
TIMER ON
Displays when TIMER ON time is set.
TIMER OFF
Displays when TIMER OFF time is set.
SLEEP
Displays when in SLEEP MODE.
FOLLOW ME
Displayed when FOLLOW ME function is activated.
TEMP./TIMER DISPLAY
Displays the set temperature (62°F~86°F). When the
operating mode is set to FAN, no set temperature is
displayed. In TIMER mode, set the ON and OFF time settings
are displayed.
FAN
Displays the FAN speed, AUTO (no display) and three
fan speed levels “
(MED) “
” (LOW )“
” (HIGH) can be indicated. The fan
”
speed is AUTO when the operating mode is in AUTO or DRY.
8
Heat Controller
DVC/DVH Remote Controller
Remote Operation
AuTO OPERATION
1. Press the MODE button to select Auto.
2. Press the UP/DOWN button to set the desired
temperature. The temperature can be set within a
range of 62°F~86°F in 1°F increments.
• In Auto mode, the unit will automatically select
Cool, Fan or Heat* modes be sensing the
difference between the actual ambient room
temperature and the set temperature on the remote
controller.
• In the Auto mode, you can not charge the fan
speed. It is being automatically controlled.
COOLING/HEATING/FAN OPERATION
If Auto mode is uncomfortable, you can manually
override the setting by putting the unit in COOL, HEAT*,
or FAN** ONLY mode.
1. Press the MODE button to select COOL, HEAT*
(pump) or FAN** mode.
2. Press the temp UP/DOWN button to set the desired
temperature. The temperature can be set within a
range of 62°F~86°F in 1°F increments.
3. Press the FAN button to select the fan speed in four
steps - Auto, Low, Med, or High.
NOTE
* Heat mode is applicable to heat pump models only.
** In the FAN mode, the set temperature is not
displayed on the remote controller and you are not
able to control the room temperature either. In this
case, only the fan speed can be changed.
9
DVC/DVH Remote Controller
Heat Controller
Remote Operation
DRY OPERATION
The DRY mode will automatically select the amount of
dehumidification based on the difference between the
set temperature and actual room temperature. The fan
speed is automatically set to low.
1. Press the MODE button to select DRY mode.
2. Press the UP/DOWN buttons to set the desired
temperature. The temperature can be set within a
range of 62°F~86°F in 1°F increments.
NOTE
• In the Dry mode, you can not change the fan speed. It
is ceing automatically controlled.
• Due to the difference between the set temperature
and the actual room temperature, the unit will
automatically switch between COOL and FAN only
mode while in DRY mode.
ADJuSTING AIR FLOW DIRECTION
Use the SWING or DIRECT button to adjust the desired
airflow direction.
1. When the DIRECT button is pushed the horizontal
louver changes in 6° degree angle increments.
2. When the SWING button is pushed the louver
oscillates.
NOTE
When the louver oscillates or moves in a position that
could affect the cooling or heating (heat pump models
only) of the air conditioner, the unit will automatically
change the louver direction.
1
2
10
Heat Controller
DVC/DVH Remote Controller
Remote Operation
TIMER OPERATION
Press the TIMER ON button to set the time the unit
should automatically turn on. Press the TIMER OFF
button to set the time the unit should automatically turn
off.
1. Press the TIMER ON button. The remote controller
show TIMER ON, the last Auto-on set time and the
“H” icon will be shown on the LCD display. Now it is
ready to reset the Auto-on time to START operation.
2. Push the TIMER ON button again to set desired Auto-
on time. Each time you press the button, the time
increases by half an hour between 0 and 10 hours
and by one hour between 10 and 24 hours.
3. After setting the TIMER ON, there will be a one
second delay before the remote controller transmits
the signal to the air conditioner. Then, after
approximately another 2 seconds, the “H” icon will
disappear and the set temperature will re-appear on
the LCD display.
TO SET THE AuTO-OFF TIME
1. Press TIMER OFF button. The remote controller
show TIMER OFF, the last Auto-off setting time
and the “H” icon will be shown on the LCD display
area. Now it is ready to reset the LCD display area.
Now it is ready to reset the Auto-off time to stop the
operation.
2. Push the TIMER OFF button again to set desired
Auto-off time. Each time you press the button, the
time increases by half an hour between 0 and 10
hours and by one hour between 10 and 24 hours.
3. After setting the TIMER OFF, there will be a one
second delay before the remote controller transmits
the signal to the air conditioner. Then, after
approximately another 2 seconds, the signal “H” will
disappear and set the temperature will re-appear on
the LCD display.
1
11
DVC/DVH Remote Controller
Heat Controller
Remote Operation
SLEEP FuNCTION
The sleep function enables the unit to automatically
change the temperature by 2°F per hour for the first two
hours, then will remain steady for the next 5 hours, after
that the unit will stop operating. SLEEP mode creates
comfortable temperatures and saves energy.
1. When the SLEEP mode is selected while in COOL
mode, the temperature increases to create the
most uncomfortable conditions while your body
temperature rises when you sleep. When SLEEP
is selected while in HEAT* mode, the temperature
deceases to ensure you don’t get too hot while your
body temperature rises when you sleep.
NOTE
The SLEEP function is only selectable when
the unit is in COOL, HEAT* or AUTO modes.
* Heat pump is applicable to heat pump models only.
1
12
Heat Controller
DVC/DVH Remote Controller
13
DVC/DVH Remote Controller
Heat Controller
14
Heat Controller
DVC/DVH Remote Controller
15
DVC/DVH Remote Controller
Heat Controller
Design, material, performance specifications and components
subject to change without notice.
ꢀꢁꢂꢂꢃ:HOOZRUWKꢃ$YHꢄꢅꢃ-DFNVRQꢃ0,ꢃꢆꢁꢇꢂꢈꢃꢃ‡ꢃꢃ3Kꢄꢃꢉꢀꢊꢋꢊꢌꢊꢋꢇꢀꢂꢂꢃꢃ‡ꢃꢃZZZꢄKHDWFRQWUROOHUꢄFRP
ꢃ
ꢃꢃ
16
07/2013
|